Saw Performace Packages and Pulleys & Belts

Looking for an inexpensive and effective upgrade for your tablesaw? The In-Line Contractor Saw Performance Package is your solution!

Machined Steel Pulleys

The standard pulleys normally installed on Contracor saws are cast pulleys. They don't run perfectly true and as a result, can create vibration in the saw. Machined steel pulleys run perfectly true and are perfectly balanced, so they will eliminate the vibration created by low quality pulleys.

Accu-Link Belt

Accu-Link link-belts run much smoother than conventional drive belts, and as a result, absorb vibration. The belt easily adjusts to length (in 3/4" increments), without tools.

The Contractor Saw Performance Package installs in just minutes, with common shop tools. In most cases, all you will need is a Hex key (Allen wrench) to complete the installation. The first time you run the saw you are going to notice:

• Vibration reduced by 90%-95%
• A much quieter running saw
• More power to the saw blade
• An improved cut by 20%-25%
  
  

Note: Most imported contractor saws, (with part numbers shown in red below) use non-standard bore pulleys on the arbor shaft. To be sure we ship you the correct pulleys, you should measure the bore of the arbor pulley before ordering. If you do not have a set of dial calipers, you should take the arbor pulley to a machine shop to have it measured.

Note: The 3/8" Accu-Link belt is a fractional horsepower belt. It will work well on machines such as Bench Top Drill Presses, but we do not recommend it for use on machines such as Table Saws. If you want to change belts on a Contractor Saw that has an original 3/8" belt, we recommend you convert to 1/2" pulleys, and upgrade to the 1/2" Accu-Link belt.

We don't cover return shipping on pulleys that were ordered incorrectly. By taking the time to measure the pulley before ordering, you will get the pulleys on your saw faster (and at less cost) than if you order the wrong pulley initially.

PP2325

Sears/Craftsman, Delta pre-1988, Ridgid, and all other saw with 5/8" bore, hub type arbor pulleys.

TR2325

Delta 10" Contractor Saw with 2 piece arbor pulley. (Held on by nut- Manufactured after Oct. 1988.)

$48.95

PP5510

Jet models with .551" (14mm) bore arbor pulley
Check Arbor Pulley bore with Dial Calipers before ordering

$48.95

PP5790

General, some Powermatic models, Harbor Freight, with .579" bore arbor pulley
Check Arbor Pulley bore with Dial Calipers before ordering

$48.95

PP5830

Grizzly, some Jet models,some Powermatic models with .583" bore arbor pulley
Check Arbor Pulley bore with Dial Calipers before ordering

$48.95

PP5910

Jet models with .591" (15mm) bore arbor pulley
Check Arbor Pulley bore with Dial Calipers before ordering

$48.95

MSP2058

Machined Steel Pulley
2" O.D. with 5/8" bore

$13.50

MSP2358

Machined Steel Pulley, Hub Type
2 1/4" O.D. with 5/8" bore

$13.50

MSP2358T

Machined Steel Pulley, Hubless
2 1/4" O.D. with 5/8 bore

$13.50

MSP2558

Machined Steel Pulley, Hub Type
2 1/2" O.D. with 5/8" bore

$13.50

MSP23551

Machined Steel Pulley, Hub Type
2 1/4" O.D. with .551" (14mm) bore

$13.50

MSP23579

Machined Steel Pulley, Hub Type
2 1/4" O.D. with .579" bore

$13.50

MSP23583

Machined Steel Pulley, Hub Type
2 1/4" O.D. with .583" bore

$13.50

MSP23591

Machined Steel Pulley, Hub Type
2 1/4" O.D. with .591" (15mm) bore

$13.50

Accu-Link Green Link Belt

ALLB38

Accu-Link Green Link Belt, 3/8" (sold by the foot @ $7.00. per foot)

$7.00

ALLB12

Accu-Link Green Link Belt, 1/2" (sold by the foot @ $7.00 per foot)

$7.00

ALLB124

Accu-Link Green Link Belt, 1/2" x 4' (sold in a 4' sleeve)

$27.95